Show us Your Interchanges!

[simlink 1,098]

Nice job, ntm! That is a very nice cloverleaf, and I like the landscaping around the SPUI.

[redfox85 659]

a compact cloverstack before I build up the area....

[Durfsurn 539]

Nice!

EDIT:

Here's mine:

  Edited February 16, 2012 by durfsurn  

[Shadow Assassin 336]

[Jazzmaster 716]

That avenue looks a bit shorter in height than the current available set.^

Question, will there be any sort of 7.5 meter raiser/digger lot to accommodate these new heights (L1 and L3 specifically; L3 would just be 15m+7.5m)? I know there's already an 8 meter raiser so frankly it wouldn't truly matter, but I figured it wouldn't hurt to ask.

  Edited February 22, 2012 by Yoshiisland  

[Ganaram Inukshuk 906]

Question, will there be any sort of 7.5 meter raiser/digger lot to accommodate these new heights (L1 and L3 specifically; L3 would just be 15m+7.5m)?

I asked the same question once, and I've been told that they only work with whole numbers, not decimal values.

However, I know of one way on how to get exactly a 7.5 meter high embankment, but it requires Rivit's tunnel mod...

[Shadow Assassin 336]

As hexadecimal doesn't seem to support floating point numbers, there's probably going to be a 7m hole-digger/raiser lot added. It means that we won't have perfectly flat overpasses, but the difference in slope will be very small and still look OK.

For the time being, though, I had to raise by 15m, drop it by 8 to get the same effect. It's a bit of a complicated work-around, but it'll suffice for now. It'll be a while before 7.5m content hits (due to the next NAM being, well, colossal in scope: Project 57, NWM upgrades, RAM phase II, SAM upgrades, improving cross-linking capabilities of projects, not to mention the afore-mentioned 7.5m content), so plenty of time to work out the hole digging lots. I'll most likely have to update that pack again to include the 7m hole digger and raiser (there were some modding mistakes I made which only manifested itself in very, very rare cases, but I know how to correct that now).

[Ded 30]

Daniel darling, you're what I like to call a "tease".

It's incredible how flat that interchange looks!

[lovre_zd 1]

Here is my first interchange. and my first upload .

[lovre_zd 1]

Here is my first interchange. and my first upload .

[catfriedrice 3]

Here is my first interchange. and my first upload .

That reminds me of the Pellissippi Parkway / I-40/75 Here in Knoxville. I had this one built earlier which works similarly to the one 2 miles east at I-40/75 west at Cedar Bluff Rd (if both directions were built the same anyway).

[simlink 1,098]

@Catfriedrice - Looks good. I like how compact it is.

[MrBrightside 3]

So this is one of my first humble attempts with the RHW. I was always afraid by its complexity, but it was imperative for the project I'm working on.

Does anyone recognize the interchange? It's not entirely accurate, but it's fairly close.

[Alejandro24 575]

Interesting interchange MrBrightside, looks functional.

Another interchange from that side project.

Explanation:

The highways doesn't have a name, actually all these are only one highway. The HGW 1 is the main entrance of the city, there are a deviation to the north trough the HGW 2.

Future Plans:

Inside the entering lane to the HGW 1, the area A, there is a isolated piece of an old neighborhood, remainder when the interchange were builded. These piece, without historical importance, will be demolished. To compensate this lost, the areas B1 and B2 will be upgraded to high density. Also there are another projects, like the finish of the bridge c through the area A, and the construction of the tunnel d under the HGW 2, for the communication of B1 and B2.

[lovre_zd 1]

[nathanthemayor 1,261]

@MrBrightside:I spy at least one of my STEX uploads in your photo....

@Alejandro24:Nice interchange there!

@Lovre_Zd:I love the compactness of that interchange!

[-JD- 41]

Just a standard cloverleaf

[Ganaram Inukshuk 906]

Just a standard cloverleaf

I don't know about you but I'm seeing U-turns where there are supposed to be left-turn loops.

[catfriedrice 3]

Just a standard cloverleaf

I don't know about you but I'm seeing U-turns where there are supposed to be left-turn loops.

So I wasn't the only one.

Yes, the North/South connection doesn't exist, it's meant to be built that way. The N Route goes directly to the airport, the S route now crosses the river using a new 4 lane road/bridge instead of the old 2 lane/ferry.

[-JD- 41]

Just a standard cloverleaf

I don't know about you but I'm seeing U-turns where there are supposed to be left-turn loops.

Whoops! Thanks for pointing that out, I'll fix it asap

  Edited March 2, 2012 by -JD-  

[Made in Erie 814 60]

This is a partial-Y split I just did that is loosely based on Flint, Michigan's I-75/475 (Grand Blanc end) split, in a region I am working on. Believe it or not, this is the first one of these I have ever done.

  Edited March 4, 2012 by ez_money412  

[Kruemel95 27]

sim city 4!

[Ryan B 35]

High-capacity cloverstack, anyone?

[okaleldar 10]

A nice big interchange with some smaller junctions as well. Labels included to clear things up(hopefully).

[rweather5 22]

Just experimenting with an interchange.

[-JD- 41]

I built this cloverleaf (and its correct this time!) using the RHW inner and outer curves, and other than the lower center exits being 1 tile closer to the over pass then they should be, it is perfectly symmetrical! Enjoy

I have since fixed the exits and finished the interchange with RHW-4 puzzle pieces, but since this was only a testing city, I have deleted it D:

  Edited March 28, 2012 by -JD-  

[timmie 988]

[brenn21 86]

Timmie great work, and I like the directional t-interchange you have

Hmm a good idea now comes to mind

  Edited March 30, 2012 by brenn21  

[rweather5 22]

[Haljackey 17,270]

/\

Why?