Trouble with offline bridge and tunnel mod

[craizedmanic 0]

After hours of removing and reinstalling mods I finally narrowed my problem done to the new offline bridge and tunnel mod. My problem is I am unable to zone or plop any building on any road. Also notice the interchange at the entrance of the city is gone. I have read over and over the steps for both Akar and the offline bridge and tunnel mod by Metro0214 and can not figure out what I did wrong. Also lost the parklet menu.  Does anyone know what I am missing that caused me to lose my snap points on the roads, and the parklets menu.

[Yayie 311]

Akar and Bridge and Tunnel mod are two different interface. You can't have both mods to work, so users may have to choose only one.

[craizedmanic 0]

Thank you for the response. I had overlooked one file, I knew that the mods did not work with each other. However there was an option for downloads in the bridge and tunnel mod for Akar. I downloaded them and placed them in the folder. Not only do I still have no parklet menu I have no bridge or tunnel options even though I have downloaded both of these mods "000 Akar 2.0.1.2.1.0.5 + bridge and tunnel.zip" & "000 Akar 2.0.1.2.1.0.5 + bridge and tunnel low.zip. I have tried both in my folder as well as one then the other at separate times. Nothing is working. I am sure it is something stupid that I am over looking like normal.

[chappers 82]

Thank you for the response. I had overlooked one file, I knew that the mods did not work with each other. However there was an option for downloads in the bridge and tunnel mod for Akar. I downloaded them and placed them in the folder. Not only do I still have no parklet menu I have no bridge or tunnel options even though I have downloaded both of these mods "000 Akar 2.0.1.2.1.0.5 + bridge and tunnel.zip" & "000 Akar 2.0.1.2.1.0.5 + bridge and tunnel low.zip. I have tried both in my folder as well as one then the other at separate times. Nothing is working. I am sure it is something stupid that I am over looking like normal.

 if you want to use yayie's grp akar , the tunnel and bridge mod and the parklets to work you have to install them in a specific configuration

 

Just take yayies high res akar first then install the the tunnel and bridging's akar and then take the lowress parklets and it should all work together, parklets are then offcourse not in there own menu but under the parks menu like advertised

[craizedmanic 0]

Thank you for your response. I do have the high res akar, then I put in mod 00-project akar2.0+ bridge and tunnel mod with low res parklets. Did not work. I then tried the high res akar with 000akar2.0.1.2.1.0.5+bridge and tunnel with parklet low res did not work. I then tried both akar bridge and tunnel mods at the same time did not work. I have tried a save and start over in game with each version but nothing has worked.

[chappers 82]

heres a screeny of the packages i used 

 

 

highlighted are the packages you need 

 

and heres how it looks ingame 

 

 

hope it helps 

[craizedmanic 0]

Thank you Chappers , I have looked over your mod list and compared to mine. Made sure I had all the files you do and then started a game. Everything seem to be working, but that was before I saved the game, exited to desktop, and then restarted game for the 3k boundaries to take affect. Once I did this I lost all snap points again and I am unable to plop and/or zone anything anywhere. So once again I am confused at what exactly it is that I am doing wrong. Thank you for your help

[Bugnug23 12]

Im not sure this is going to work for you but i was having the same problem, first if you are going to use a raised road, tunnel or a bridge outside the 2k boundary you need to connect with a normal road (as in a regional road) from one of the roads in the 2k zone, then you can connect a 2m road, a higher road (20m) a bridge or a tunnel after that. See below for a basic diagram

 

2k Zone road > 3k Regional Road > Raised Road, Bridge or tunnel

 

Good luck

[craizedmanic 0]

I am sorry I was not clear. When I say I can not plop or zone I mean on basic road types. I can start a city draw an ave out form the city entry and I can zone, plop, whatever. But then without doing anything but laying out the ave, save the game exit to desktop and then restart the city, and all the snap points are gone and no more zoning abilities. I don't even make it to using any other type of mod and or regional road types. Its just strange to me that before the 3k boundaries take over it seems to work, but after it does I can not even build within the actual city. Once I reload the game all I can do is lay out roads. I apologize I did not explain it more clearly.

[Nico Robin 70]

i'm Using Bridge and tunnel mod with Parklet work fine for me

look here :

[Bugnug23 12]

I am sorry I was not clear. When I say I can not plop or zone I mean on basic road types. I can start a city draw an ave out form the city entry and I can zone, plop, whatever. But then without doing anything but laying out the ave, save the game exit to desktop and then restart the city, and all the snap points are gone and no more zoning abilities. I don't even make it to using any other type of mod and or regional road types. Its just strange to me that before the 3k boundaries take over it seems to work, but after it does I can not even build within the actual city. Once I reload the game all I can do is lay out roads. I apologize I did not explain it more clearly.

 

Ah ok i see what you mean, i've never run into that problem seems like game mechanics to me. do you run the game as admin every time? if not then the game can get a bit funny at times. 

[Ciaolo 15]

Use this package that could solve your problem.

 

Tell us if it does or doesn't.

If it does, we need to tell the mod author to do a little change in his/her mod.

0000-bridge-tunnel-fix.zip

[charlesnew 262]

Thanks Ciaolo!

 

It worked! Now I can go back to playing SimCity!

[craizedmanic 0]

Thank you so much Ciaolo for the help. Thanks to everyone that has help for that fact. I am sorry it has taken so long to get back to you guys, but the bridge and tunnel fix worked. So far everything seems to be working right. Thanks again

[xoxide 377]

@Ciaolo Thank you for that patch to help users. i appreciate that

[Johan81 0]

does not work new akar menu 

[paiom 1]

On 7/30/2014 at 3:19 PM, Ciaolo said:

Use this package that could solve your problem.

 

Tell us if it does or doesn't.

If it does, we need to tell the mod author to do a little change in his/her mod.

0000-bridge-tunnel-fix.zip

Downloaded the file but when i'm going to extract it, says: The archive is either in unknown format or damaged!

I really need it. anyone can upload the file again?  it's just 340 Bytes?